Seats & Harnesses
Rock Ready Polaris Gen 4 Adjustable Angle Seat Lower and Tilt Base Adapter Seats & Harnesses Seats & Harnesses
Polaris Gen 4 Adjustable Angle Seat Lowering and Reclining Base Adapter
The all-new Generation 4 seat base is finally here! You can now adjust your lean angle via 4 carriage bolts. This is the original drop and tilt seat base that holds the factory slider. Adjustable tilt and slider make this the most versatile drop seat base on the market. Whether you play in the rocks and want to be more upright but still comfortable, or you're a laid-back cruiser, there's a frame for everyone. Rock Ready UTV Gen 4 bases also have more slider adjustment slots than the factory seat base. This allows people with 4-seat custom cages to gain even more legroom!
These seat bases were designed to work with the stock seats. We try to make these bases fit as many seats and applications as possible, but we cannot guaranteethat they will work with everything. So far they have been tested with Simpson (formerly Twisted Stitch) seats, PRP seats and Pro Armor seats. The amount of adjustment with Simpson seats is limited. This is due to the seat latch hitting the bottom of the seat. Bases do not work with Beard seats, Yamaha utv parts Canada, quality utv parts, side by side utvs near me, Corbeau, East Lake utv parts, utv parts in Canada, Hisun 800 parts utv or Triple X seats. The seat latch interferes with the steel seat frame in the rear. Contact us for more information on how to test new applications without risk.
4-seater seats with factory cages will be limited in terms of seat backset due to the bar on the cage directly behind the seat. You can either use it this way or cut this bar to use the full range of adjustment and lowering ofthe base of the seat. The stock Turbo S 4 seat cage limits the depth of seat adjustment where the 4-point seat belts are mounted on the cross tube.
General owners. Generals have a more vertical firewall than a RZR. Although this base fits the machine, it was designed for the RZR. If used in general, the seat will need to move a few to clean the firewall plastic. The plastic at the bottom can be heated and pushed down for more space to push the seat further back. Adjusting the seat base to a lesser angle also allows the seat to be moved further back. The General 4 Passenger model front seats will rub on the front seat belt housing when used with a stock roll bar and factory seat belt positions while the seat is adjusted in the positions the rearmost ones. The rib of the plastic on the partrear of the lower seat cushion may catch on the plastic latch when the seat is fully adjusted rearward. This rib can make it difficult to slide the seat forward once it has been fully adjusted to the rear notch.
Gen 3 and Gen 4 seat base differences. The basics Gen 3 seats recline 7 degrees and lower the head approximately 2″. This means that some machines will require the seat to be moved forward if the top of the seat hits the firewall or hits the harness tube on 4-seater vehicles. ThThe Gen 4 seat base has 3 tilt adjustments via carriage bolts. Depending on the set of holes the carriage bolts are installed in, the seat will recline 3.5 degrees (head drop 1.5 inches), 5.2 degrees (head drop 1 .75 inches), or 7 degrees (head lowering 2 inches). The slider notches are also dlaser cut into the Gen 4 seat base so you don't reuse the factory zinc coated part. Generation 4 also has longer slots and an additional notch to potentially gain legroom in 4-seater machines with aftermarket cages that have the harness bar further back than the harness bar. factory.
Warranty Information: Rock Ready UTV Seat Bases Backed by a lifetime warranty for the original purchaser. The warranty covers the structural sheet steel portion of the seat base. Misuse or seat bases that have been altered from new condition will not be warranted. Powder coating, latches, used UTV parts on eBay and hardware are not covered under warranty.
Features:
- Lean Angle adjustable (3.5°, 5.2°, realtree xd utv 24v steering parts, 7°)
- Can be used with or withoutfactory slider
- More rear adjustment than factory seat base
- Lowers seat back 2+" depending on recline adjustment
- li>
- Lowers rear seat base by 3/4"
- CNC laser cut and formed
- 3/16" steel construction
- Powder coated black
- Includes all hardware and instructions
- Choose a single or a pair
- Polaris General 1000
- Polaris RZR RS1
- Polaris RZR S 1000
- Polaris RZR S 900
- Polaris RZR Turbo S
- Polaris RZR XP 1000
- Polaris RZR XP Turbo
Instructions
ATS-POL-GEN Make_Polaris, Model_General, Model_RZR RS1, Model_RZR S 1000, Model_RZR S 900, Model_RZR Turbo S, Model_RZR XP 1000, Model_RZR XP Turbo Quantity:Single,Pair4.92 (589 reviews)
