Seats & Harnesses
Rock Ready Polaris Gen 3 Seat Lower and Tilt Base Adapter Seats & Harnesses Seats & Harnesses
Polaris Gen 3 Seat Lowering and Reclining Base Adapter
These seat bases were designed to work with the stock seats. We try to make these bases fit as many seats and applications as possible, but we cannot guarantee that they will work with everything. So far they have been tested with Simpson (formerly Twisted Stitch) seats, PRP seats and Pro Armor seats. The amount of adjustment with Simpson seats is limited due to the seat latch hitting the bottom of the seat. The bases will NOT work with Beard, Corbeau, utv side by side near me, quality utv parts, yamaha canada utv parts or Triple X seats because the seat latch interferes with the steel seat frame at the back. Contact us for more information on how to test new applications without risk.
4-seater seats with factory cages will be limited in terms of seat backset due to the bar on the direct cagent behind the seat. You can either use it this way or cut this bar to use the full range of adjustment and lowering of the seat base. The front seats of the General 4r seat will rub on the front seat belt housing when used with a stock roll cage and factory seat belt positions while the seat is adjusted to the correct positions. further back. The stock Turbo S 4 seat cage limits the seat adjustment depth where the 4-point seat belts are mounted on the cross tube.
RS1 cannot use the last 3 notches of the seat slider. The bottom of the seat base touches the fuel tank cover but still fits and works. You will still lower your head more than 1" (see photo.) I still had plenty of leg room and I'm 5'11", East Lake utv parts, utv parts in canada, Hisun 800 utv parts, parts Bobcat utv 3400 , 200 lbs.
Generals have a more vertical firewall than a RZR. Although this base fits the machine, it was designed for the RZR. If used in general, the seat will need to move forward a little to clear the plastic from the firewall. The plastic at the bottom can be heated and pushed down for more space to push the seat further back. We highly recommend the Gen 4 Restoration Bases for use in the General's Siege Bases instead of the Gen 3 Siege Bases.
Differences between Gen 3 and Gen 4 Siege Bases. Gen Siege Bases 3 reclines 7 degrees and lowers the head approximately 2″. This means that some machines will require the seat to be moved forward if the top of the seat hits the firewall or hits the harness tube on 4-seater vehicles. The Gen 4 seat base has 3 tilt adjustments via carriage bolts. Depending on the set of holes in which the carriage boltsare installed, the seat will recline 3.5 degrees (1.5 inch head drop), 5.2 degrees (1.75 inch head drop), or 7 degrees (1.75 inch head drop). 2 inches). The slider notches are also laser cut into the Gen 4 seat base so you don't reuse the factory zinc coated part. Generation 4 also has longer slots and an additional notch to potentially gain legroom in 4-seater machines with aftermarket cages that have the harness bar further back than the harness bar. factory.
Warranty Information: Rock Ready UTV Seat Bases have a lifetime warranty to the original purchaser. The warranty covers the structural sheet steel portion of the seat base. Misuse or seat bases that have been altered from new condition will not be warranted. Powder Coating, Used UTV Parts eBay,latches, Realtree XD UTV 24V steering parts and hardware are not covered under warranty. factory
- Polaris General 1000
- Polaris RZR RS1
- Polaris RZR S 1000
- Polaris RZR S 900
- Polaris RZR Turbo S
- Polaris RZR XP 1000
- Polaris RZR XP Turbo
Instructions
TSS-GEN16 Make_Polaris, Model_General, Model_RZR RS1, Model_RZR S 1000, Model_RZR S 900, Model_RZR Turbo S, Model_RZR XP 1000, Model_RZR XP Turbo Quantity:Single,Pair4.75 (572 reviews)
